Asphalt Plant Equipment For Sale - New & Used Asphalt, Concrete & Crushing Plants

Make: Heatec Model: HC-200 Combo- oil/gas Ran on Natural Gas Honeywell Gas Valve Electric Motor Motor Make: Lincoln Serial: U1930112791 Volts: 230/460 HP: 7.5 Phase: 3 100 Gallon Oil Capacity Circulating Pump Rate: 92GPM Pump HP: 7.5 BTU: 2,000,000 Burner Make: PowerFlame Model: C2-OP SN: 37820003 Advance Thermal Corp Skin for Tank and Lines Complete with Controls Skid Mounted DOES NOT HAVE FAN OR FAN MOTOR FOR BURNER

Make: Heatec Model: HC300C SN: H81046 Year: 1981 Fuel Source (Combo Oil/Gas) Has Gas Train Has Fuel Pump and Filter Circulating Pump Updated Fire Eye Expansion Tank

Make: SN: JNB 6727 Max Water Temp: 5331 Safety Valve Rel. Cap: 500 Year: 2007 Repaired 11/17/2023 by Ashley Mechanical Inc. Powerflame Natural Gas/Fuel Oil Burner Condition Notes: Has leak that will need to be welded. Used until April 2024. Was set up as a steam boiler for hot water for a concrete plant.

Heatec Heater 700,000mbtu HCS-70 SN: HOO-058 Year: 04-00 Powerflame burner, Model C1-GO-12 Fire Eye, Digital Temp Controllers, Updated Siemens Breakers and Starters Combo Hot Oil Heater Honeywell Gas Valve Diesel Pump Skid, 10hp Disconnected and ready to load on buyer's trailer.

Make: CEI Model# 1500-A SN# H112/95 Year# 1995 Fuel Source Single Fuel (Nat Gas) This heater has a large Expansion Tank, And a Heat Recapture Box, with Nat Gas Train and hot oil circulation system. This heater has been kept as a back up system for a west coast company to go into service at a moments notice.

Hy-Way MKGO-750 SN: 4119 7.5 MMBTU gas/oil thermal fluid heater Completely rebuilt Stack economize 500 gallon expansion tank **Portable frame does not go with sale, owner used to move while on sites**

PX120 Heater This heater is rated for up to 125 PSI @ 650 deg f. The heater will net out 12.0 MMBtu/Hr. Manufacture time approx 14 weeks. CALL FOR PRICE

Heater 1.5 MBTU Powerflame burner Model#: C2-GO-15 SR#: 020307746 Dual fuel (diesel/gas) Partial gas train and fuel pump Skid mounted 2’x 5’ expansion tank Circulation pump 10hp motor NEMA control cabinet with fire eye Parlow temp controls

1.2 MBTU Heatec 5hp motor Skid mounted Powerflame burner Model#: HCS:70:C SR#: H87:135 Dual fuel (diesel/gas) Model#: C1-GO-12 SR#: 078738569 Expansion tank Circulation pump NEMA control cabinet (can’t see fire eye) Partlow temp controls Shipping Dims: 7’x 4’

Used 20 MMBTU/Hr Hot Oil Boiler. Manufactured by Sigma Thermal. Model HC2-17.5-H-SF. 5861kW. 2064 Sq Ft Heat surface. 400F @ 52PSIG. 350059 lb/hr mass flow. Media: Chemtherm 550. Serial #J12012.

Make: Gencor/Hyway Model: HYFGO 100 SN: 5009 Circulating Pump Package Combo Burner (Oil/Gas) Partial Gas Trane Fuel Pump And Filter No Exspantion Tank Unit has coking in the coils

PARTS HEATER EXPANSION TANK MAKE: CEI

Gentec Hot Oil Heater 1.2 MBTU Power Flame Burner Model C1-GO-12 SN# 059050034 OIL/GAS Honeywell Gas Valve / Webster Fuel Pump Expansion Tank Hot Oil Circulating Pump and Motor Approximate Shipping Dims 6’6” w x 20’ long x8’4” tall

Used 11mbtu Heatec Hot Oil Heater Model: HCI-8010-50-G SN: HI17-094 Date: 09-17 6" Lines 300psi valves Natural gas valves control pack heat exchange Never Been Installed CM9-G-30 Power Flame Burner, Natural Gas Has expansion tank Purchased New for Approx $2.5-3million MISSING PUMP PACKAGE

**Make**: Heatec **Output**: 1.2 MBTU **Combo** (Running on Gas) **Other:** * Has gas train and fuel pump * Was running on gas * Made in the USA

One Phoenix Thermal oil heater; model PX-100, maximum design temperature of 550°F. Double Helical coil design with heatmizer fins for improved heat extraction from air stream. The unit will be complete and ready to fire after connecting to the electric, fuel, and hot oil circulation piping. The coil is designed according to ASME for 550°F @ 125 psi MAWP. The coils are Schedule 40 SA-106B pipe. This unit comes with a reconditioned burner with a two year warranty on all burner parts. Includes the following specs: • 6" inlet/outlet nozzles - ANSI 300# SA 105 WNRF flanges. • ASME designed coils = 125 psi @ 550°F. • Double 3” helical coils. (Sch. 40 SA-106B Seamless pipe). • The heater shall have high temperature refractory install in the turn-around area of the heater. • Shell and front/back plates to be 304 SS 5/16" steel wrapped with 2" thick high temperature insulation covered with a galvanized steel skin. • The heater shall be equipped with a 2" diameter sight glass (quartz) port equipped with a cooling connection located at the rear of the unit for an unobstructed view of the flame. • The heater shall be equipped with a 20" (minimum) manway located at the rear door for internal inspection of the unit. • The heater shall be equipped with sampling and instrumentation ports to be located on the stack and at locations before and after the convection section. • All electrical conduit material shall be rigid aluminum. Controls Controls and control panels to meet NEMA 4 requirements and includes the following: • UL Listed NEMA 4 enclosures. • TEFC burner blower motor. • Honeywell high oil temperature limit control. • Love Controls TCS-4010 high stack temperature control. • 1 - Stack dual thermocouple. • Square D 500SV1B Step-down control transformer for 120V control power. • Numbered terminal blocks and enclosed wire raceways. • Alarm horn mounted to the control panel. • Integrated shutdown permissive. • Control Relays. • Full set of dry contacts for alarms and statuses for customer use. • Push/Pull emergency stop button located on control panel. Locally mounted instruments: Heater Inlet Piping: • 1 –pressure switch mounted between the heater inlet and outlet for 500 GPM flowrate. • 1 - Inlet pressure gauge with shut off cock. • 1 - Inlet thermometer with thermowell. • 1 – Inlet thermocouple. With thermowell. Heater Outlet Piping: • 1 - Outlet pressure gauge with shut off cock. • 1 - Outlet thermometer with thermowell. • 1 - Outlet dual thermocouple with thermowell. • 1 – Outlet thermocouple with thermowell for circuit coil #1 • 1 – Outlet thermocouple with thermowell for circuit coil #2 • 1 –Flanged pressure relief valve (located on the heater outlet manifold). Pilot Fuel Train (Natural Gas): Pilot fuel train designed to meet typical NFPA-87 / NEC requirements. Pilot fuel train controls to meet NEMA 4 requirements. The pilot fuel train will be constructed of carbon steel threaded connections. The pilot fuel train shall include the following: • 1 – Pilot fuel pressure regulator. • 2 - Automatic safety shut off valve. • 1 – Solenoid vent valve. • 2 - Manual shut off valves. • 1 - Pressure gauge with isolation valve. Main Fuel Train (Natural Gas): Main fuel train designed to meet typical NFPA-87 / NEC requirements. Main fuel train controls to meet NEMA 4 requirements. The main fuel train will be constructed of carbon steel threaded connections. The main fuel train shall include the following: • 1 – Main fuel pressure regulator. • 1 - Carbon steel strainer. • 2 - Manual shut off valves. • 2 - safety shut off valves with proof of closure switches. • 1 – Solenoid vent valve. • 1 – Low gas pressure switch with manual reset switch. • 1 –High gas pressure switch with manual reset switch. • 2 - Pressure gauges. **CALL FOR PRICE. QUOTES ARE GOOD FOR 7 DAYS!**

Proposal for one PX-200 Hot Oil Heater: One NEW Thermal oil heater; model PX-200, max design temp of 550°F. Double Helical coil design with heatmizer fins for improved heat extraction from air stream. Natural gas power burner with full modulation rated at 25.2 Mmbtu/hr. The unit will be complete and ready to fire after connecting to the electric, fuel, and hot oil circulation piping. The coil is designed and stamped according to ASME for 125 psi MAWP. The coils are SA-106 seamless pipe. Heater maximum output: 20.0 Mmbtu/hr. Based on supply/return ?T of 100°F and a hot oil flow rate of 600-gpm. More Information Available. Manufacturing Time 12-14 Weeks *Pricing and manufacturing time as of 11-22-22. Pricing and Manufacturing time is subject to change. A new quote will more than likely need to be provided if request is more than 30 days from pricing previous pricing date.*

We have a 10mmbtu and 5.5mmbtu hot oil heaters for sale. Please call for more information!

**Make**: CEI **Output**: 1mbtu **Year**: late 80s model **Natural Gas** **Other**: * Ray burner should also be able to burn diesel * It has a Peerless pump

The boiler comes on trailer complete with a Low NoX FGR burner and includes a stub stack and economizer. The unit will pass a hydro and have included $10,000 worth of spares that we would include. We would make available our technician to do a 4 day training/ maintenance course with the new owner. Serial Number: 0-3673 Tag: 7630-CS Serial Number: 0-3674 Tag: 5808-DR Vin Numbers for Trailers On File

**Make**: Heatec **Model**: HFP-100R **SN#**: H04-304 **Year:** 12-04 **Other**: * Inline Hot Oil (Thermal Fluid) Heated Fuel Pre-Heater * Fuel Pump * Duplex Filters * Modulating Controls (For Maximum Fuel Savings) * Skidded * Fuel Pre-Heater

**Make**: Heatec **Model**: HFP-100R **SN#**: H05-066 **Year:** 03-05 **Other**: * Inline Hot Oil (Thermal Fluid) Heated Fuel Pre-Heater * NO FUEL PUMP * Duplex Filters * Modulating Controls (For Maximum Fuel Savings) * Skidded * Fuel Pre-Heater

* Capable of heating up to 1000 gallons per hour (averages 600-1000gals per hour) * Heated via hot oil * Insulated preheater * Oil to oil heater- heats fuel oil * Comes ready to accept inch and a half oil lines and inch and a half hot oil lines * Available to ship within 3 to 4 weeks of order CALL ASI WITH ANY QUESTIONS!

**PRE-HEATER** **Electric** **Other:** * Process Heating Pre-Heater *HEATING SOURCE* ( Electric) *Rating:90KW"

**Make**: Gencor **Model**: ES-8 30H 230V **Serial Numbe**r: 003-101517 **Other**: * Pre-Heater * Air Pressure Rating: 125/135psig

Heatec Pre Heater Job # H08-055 480 V 3 PH 60 HZ MAx Current AMPS: 450 (Heating Source "Electric") Nema Encloser with Electrical Equipment 10 HP Pump Source

Pre Heater Hy-Way Electric 4 Elements Skin Rough Control Panel

Used Pre-heater

**Year**: 1992 **Other**: * Infernotherm * Oil Heater * Pre-heater